Find or Sell Motorcycles & Scooters in USA
Honda > Honda CB

1983 Honda Cb1100f Canadian Model on 2040-motos

US $7,500.00
YearYear:1983 MileageMileage:13672 ColorColor: Blue
Location:

Moose Jaw, Saskatchewan, CA

Moose Jaw, Saskatchewan, CA
QR code
1983 Honda CB1100F Canadian Model, US $7,500.00, image 1

Honda CB photos

1983 Honda CB1100F Canadian Model, US $7,500.00, image 2 1983 Honda CB1100F Canadian Model, US $7,500.00, image 3 1983 Honda CB1100F Canadian Model, US $7,500.00, image 4 1983 Honda CB1100F Canadian Model, US $7,500.00, image 5 1983 Honda CB1100F Canadian Model, US $7,500.00, image 6 1983 Honda CB1100F Canadian Model, US $7,500.00, image 7

Honda CB tech info

TypeType:Sport Bike Engine Size (cc)Engine Size (cc):1062 WarrantyWarranty:Vehicle does NOT have an existing warranty For Sale ByFor Sale By:Dealer

Honda CB description

Fuel tank,sidecovers,guages and rear tail piece replaced back over 10 years ago while you could still buy them new from Honda Canada.They are now obsolete and no longer available.Older pieces were kept by the previous owner and resold...they were faded somewhat but were not replaced due to any damage.The previous owner had 3 of these which 2 were traded off to us.This one was the least used with approx 22,000 kilometers.The bike had sat for years in a shop and when we went to first start the bike again a ring snagged and broke so we removed the cylinder block, honed the bores and installed new factory rings along with the new gaskets and seals as required.We also adjusted the valve clearances and cleaned the carbs.The oil & filter was changed using fresh Honda GN4 10-40 .It was recently test ridden and runs flawlessly.The back tire is near new while the front has some wear.We have the original airbox which had some mods done to it to increase air-flow.We also have the stock signal lights.The seat is a Corbin gunfighter.The carbs have a dyno jet kit installed along with the seperate K&N air filter pods.We do not have the stock seat or exhaust system.

Any shipping or transportation costs will be up to the purchaser

Moto blog

GSX-R600 and CBR250R the glass is half full

Wed, 13 Oct 2010

Suzuki’s GSX-R600 might not look that much different to the outgoing model but I suspect this bike could be very much a dark horse in 2011. I say this because two years ago I was definitely not building my hopes up en route to the K9 GSXR 1000 launch. The leaked pictures suggested the biggest change from the 2007 version would be some fresh graphics but I was so wrong.  As it turned out, I was greeted in Almeria with a brand new bike, built from the tarmac up and it proved to be more than a match in every department for the much hyped 2009 Yamaha R1.

FIM to Revise WSBK Homologation Requirements

Fri, 17 Jan 2014

The International Motorcycling Federation is considering modifying its homologation requirements for the World Superbike Championship following Bimota‘s somewhat surprising plans to re-enter the series. Under current regulations, manufacturers must produce a minimum number of motorcycles for it to be eligible to compete in the production-based WSBK championship. The official regulations currently require a minimum of 125 units produced for an initial homologation inspection, 500 units produced by June 30 of the current year, 1,000 units by the end of the current year and 2,000 units by the end of the following year.

2015 Honda PCX150 Announced for US

Tue, 01 Apr 2014

American Honda announced it will bring the updated PCX150 scooter to the U.S. as a 2015 model. Revealed earlier this year for the European market, the 2015 PCX150 receives a larger fuel tank, improved fuel economy and a new look.

2040Motos.com © 2012-2024. All Rights Reserved.

Designated trademarks and brands are the property of their respective owners.

Use of this Web site constitutes acceptance of the 2040Motos User Agreement and Privacy Policy.

0.7 s, 4797 u